Home Improvement

Tips for cutting vinyl plank flooring

Make sure you’re operating safely before you start cutting into a vinyl plank. Make certain you’re wearing gloves.

Always cut with the plank’s decoration facing up. Draw a cutting line with a pencil at the measured location and then firmly cut through the board and break it in half, with the ornamentation pointing away from your body.

A set of pliers or a similar tool is a lot more practical option if you simply need to break off a little edge.

Read also: samsung tv red light blinking

Cutting your planks into a unique form shouldn’t be difficult. Break the form out of the vinyl plank by cutting it into the board and making sure the cuts are snug.

How to cut vinyl plank flooring?

Here are some quick steps on how to cut vinyl plank flooring. Follow these simple steps to do properly.

Step-1

You’ll need to check the subfloor first as Alpha Vinyl can manage most abnormalities. In this case, we recommend that you start by ensuring the surface is level Because, sturdy and clean, as well as removing any old floor coverings.

What is the maximum size of the joints in your present tile floor? How do you even out inconsistencies? What about radiant heating in the floor?

Step-2

A better-looking, more solid, and pleasant floor may be achieved with the correct underlay. We provide a variety of Alpha Vinyl-compatible underlays.

Take following tools,

  • A hammer.
  • a saw that can be used to cut vinyl.
  • a mouthpiece
  • a measuring tape
  • Safety glasses are required.
  • To measure the corners, use a bevel.
  • Use tape to secure your underlay.
  • cleaning supplies
  • a slender strand of rope
  • gloves.
  • a piece of paper and a pencil
  • a compound for leveling
  • calculator.

a pull-bar, spacers, and a tapping block from the Quick-Step installation package

Step-4

It’s all about to end! Step 2: Roll out your underlay and press it against the wall as tightly as possible. Lay one row at a time, making sure you’re going in the same direction as your floor (see step 5). To prevent damage, use adhesive tape to connect the rows.

Step-5

Divide the width of the room by the width of a plank to get how many full rows of planks you’ll need.

Mark the spot on the wall where you’ll put your final complete plank. To guarantee simple installation, the last board should be at least 5 cm broad.

To prevent placing identical patterns and color variants too near together, unpack your planks and vary them up.

Start placing your first row of Alpha Vinyl planks in line with the longest wall, but not flush against it, for the greatest results (as walls are hardly ever perfectly straight).

Ensure that the end joints of subsequent rows are never aligned in the same direction. We propose a minimum distance of 30 centimeters between them.

Step-6

To complete your floor, you’ll have to cut your Alpha Vinyl planks. Wear gloves and draw your cutting lines with a pencil. Always saw your boards with the design on the top surface facing up.

Step-7

Circular saws are power instruments that can cut a variety of materials using a variety of circular blades. They are the most user-friendly and versatile saw on our list, since they are used to frame houses, build decks, and other DIY projects.

Given the variety of models accessible to homeowners today, we believe they are also reasonably priced. Depending on your budget, these powerful instruments might cost anywhere from $40 to $200.

There are cheap solutions available, such as the SKIL 5280-01, which has a laser guide to assist homeowners in maintaining a straight line. Along with quality corded circular saws, cordless circular saws are an option.

Step-8

Homeowners who choose not to use powered equipment or who prefer greener alternatives also have a choice. Certain forms of flooring, such as laminate and vinyl, are popular among floor and siding cutters. These instruments, however, are manual and more costly than most circular saws.

When shopping for a cutter in this category, be sure to look at the sorts of vinyl it can cut as well as the sizes it can handle. This Marshalltown cutter can handle flooring up to 8″ wide and up to 12mm thick laminate or vinyl flooring.

Last word about article

Before we get into the tools you’ll need to install vinyl flooring properly in your house, let’s take a look at the procedure itself. We go over it in detail in our vinyl flooring installation guide, but there are a few things to keep in mind before you start.

Read also: Benifits of choohing vinyl plank flooring!

Vinyl plank flooring is available in a variety of forms, the most common of which being LVP, WPC, and SPC. Peel and stick vinyl planks are technically included in this category, but they’ll be discussed separately.

Related Articles

Leave a Reply

Your email address will not be published.

Back to top button